Digital Angle Finder – 4-Side Magnetic Base, Built-In Laser, USB Rechargeable
Digital Angle Finder – 4-Side Magnetic Base, Built-In Laser, USB Rechargeable
Free Delivery & Easy Returns
Buy 2+ Items, Save 10%
Details
Magnetic on 4 sides · Built-in laser · USB rechargeable
Dial In Exact Angles Without the Guesswork
This compact digital angle finder brings precise angle readings, magnets on all four sides and built-in laser guides together in one small, workshop-ready tool. Use it to set saw blades, check slopes, set bevels, line up machines and mark exact reference angles, then drop it back in your pocket.
Precise readings
Clear numbers you can trust
The angle finder reads in steps of 0.05° with an accuracy of ±0.1°, over a full 4 × 90° measuring range. That makes it easy to dial in 45°, 90° or any custom angle for saw setup, levelling, installation and alignment work.
The bright, backlit display turns itself the right way up, so the numbers are easy to read in any position.
Hands-free hold
Sticks on from any side
Strong magnets are built into all four sides. The tool holds firmly on saw blades, steel pipes, machinery and other magnetic metal surfaces, in whatever position the job needs, so both your hands stay free for the adjustment.
For the strongest hold, make sure the contact surface is clean, flat and made of magnetic metal. On wood, worktops, walls, floors, plastic and other non-metal surfaces, simply place or hold the tool against the surface to measure.
Laser guides
Measure here, line up over there
Built-in laser guides carry the tool's direction far beyond its small body. That makes it easier to line up shelves, cabinets, pipes, fixtures and long workpieces.
Choose the left laser, the right laser or both, to suit the job.
Two ways to measure
Measure from the surface that matters
Not every bench, floor or machine is perfectly level. In absolute mode, the tool measures the angle against true horizontal level.
In relative mode, you set your own starting point: place the tool on your reference surface and press ZERO. That surface now reads 0.00°, and every reading after that is measured against your actual table, machine or workpiece.
Degrees or slope
Two units at the touch of a button
Read angles in degrees, or switch to slope in percent for ramps, drains and gradients. Hold the HOLD button for about 2 seconds to toggle between ° and %.
Simple controls
Four buttons, all you need
The controls are simple and quick to learn.
- Power on and off: press briefly to switch on. Press and hold for about 3 seconds to switch off.
- Laser: after switching on, press the same button to cycle the laser: right side, left side, then both sides.
- HOLD: press briefly to freeze the reading on the screen. Press again to release it.
- ZERO: place the tool on your reference surface and press ZERO to reset the angle to 0.00°.
Saw setup
Calibrate a table saw or mitre saw blade
1. Switch off the saw
Always switch off and unplug the saw before you attach, remove or adjust the tool.
2. Zero on the table
Place the angle finder on the saw table and press ZERO.
3. Attach it to the blade
Let the magnets hold the tool against the blade.
4. Adjust the blade
Tilt the blade until the display shows the exact angle you need.
Ideal for
From the workshop to the home
It is a handy tool for woodworkers, metalworkers and anyone doing DIY around the house.
- Table saw and mitre saw calibration
- Saw blade bevel and 90° setup
- Drill press and machine table adjustment
- Level, slope and angle measurement
- Cabinet, shelf and fixture installation
- Metalworking, fabrication and pipe alignment
- Home improvement and general DIY projects
Built to last
Rugged and always ready
The outer shell is made of tough aluminium alloy, built for everyday workshop bumps and daily use.
The built-in battery recharges by USB, so you never need to buy disposable batteries.
Pocket-sized
Always within reach
At just 60 × 60 × 30 mm (2.36 × 2.36 × 1.18 in), it fits easily in a pocket, tool pouch or drawer, so it is ready whenever you need it.
Questions people ask
How accurate is it?
It reads in steps of 0.05° with ±0.1° accuracy over a full 4 × 90° range, ideal for 45°, 90° and custom angles.
Does it work on non-metal surfaces?
Yes. It measures on wood, worktops, walls, floors, plastic and other non-metal surfaces. The magnets only hold it hands-free on magnetic metal; on other materials, place or hold the tool against the surface.
What is the difference between absolute and relative measuring?
Absolute mode measures against true horizontal level. For relative measuring, place the tool on your chosen reference surface and press ZERO, so that surface reads 0.00° and all readings are measured against it.
Can I use it to set my saw blades?
Yes. Place it on the saw table, press ZERO, then attach it to the blade with the magnets and adjust the blade until the display shows the angle you need. Always switch off and unplug the saw first.
How strong is the magnetic hold?
Magnets on all four sides hold it securely in several positions on saw blades, steel pipes, machinery and other magnetic surfaces. A clean, flat metal surface gives the strongest hold.
Is it rechargeable?
Yes. It has a built-in battery that charges by USB.
Specifications
- Resolution: 0.05°
- Accuracy: ±0.1°
- Measuring range: 4 × 90°
- Units: degrees and slope percentage
- Modes: absolute and relative
- Magnets: on all four sides
- Laser: left, right or both sides
- Functions: ZERO, HOLD, auto-turning backlit display
- Housing: aluminium alloy outer shell
- Size: 60 × 60 × 30 mm (2.36 × 2.36 × 1.18 in)
- Power: built-in USB-rechargeable battery
What's in the box
- 1 × digital angle finder